Furnace Filter Sizes and How Often to Change Them in Calgary

Quick answer: Check the size printed on your current filter’s frame, such as 16x25x1. In a Calgary winter, change a standard 1-inch filter every 1 to 3 months, monthly with pets, and a 4- or 5-inch media filter every 6 to 12 months. Change it sooner after renovation dust or wildfire smoke. A clogged filter is a common cause of furnace shutdowns.

The furnace filter is the cheapest part of your heating system and one of the most important. A clean filter keeps air moving, protects the furnace from dust and helps your home’s air. A clogged one can make the furnace overheat, shut itself off and wear out sooner. Here’s how to find the right filter, how often to change it in a Calgary winter, and the mistakes that trip people up.

Where to Find Your Furnace Filter

Most furnace filters sit in one of three places:

  • A slot beside or below the furnace, between the cold-air return duct and the furnace, often behind a small cover or door.
  • A media filter cabinet, a thicker box beside the furnace that holds a 4- or 5-inch filter.
  • A return-air grille on a wall or ceiling, in some homes and condos.

Turn the thermostat off or set the furnace fan to Auto before you open the filter slot.

How to Read Your Filter Size

The size is printed on the edge of the frame, written as width x height x thickness, for example 16x25x1 or 20x25x5. This is the nominal size, rounded for easy shopping. The real size is a little smaller, for example 15.75 x 24.75 x 0.75 inches for a 16x25x1 filter. That’s normal; always buy by the nominal size printed on the old filter.

If there’s no label, measure the old filter or the slot and round up to the nearest standard size. Don’t force in a filter that’s too big or leave gaps around one that’s too small, because unfiltered air will go around it.

1-Inch vs 4- or 5-Inch Filters

Filter typeProsCons
1-inch filterCheap, available everywhere, fits most standard slotsSmall surface area, clogs fast, needs changing often
4- or 5-inch media filterLasts much longer, filters better without choking airflowNeeds a media cabinet; each filter costs more

If you’re changing 1-inch filters every month, or someone at home has allergies, a media cabinet is worth considering. It’s an easy addition during a furnace tune-up or furnace installation.

How Often to Change It in Calgary

Your home1-inch filter4- or 5-inch media filter
Typical household, winterEvery 1 to 3 monthsEvery 6 to 12 months
Pets or allergiesEvery monthEvery 4 to 6 months
Renovation dust or new-build dustCheck weekly; change as soon as it’s greyCheck monthly
After a wildfire smoke eventChange once the smoke clearsCheck and change if discoloured

The calendar is only a guide. The best test is to pull the filter out once a month during the heating season and hold it up to a light. If you can’t see light through it, change it. A simple habit is to check it when the gas bill arrives.

Which MERV Rating Should You Buy?

MERV is a rating from 1 to 16 for how fine the particles a filter catches are. Higher isn’t automatically better: a very dense filter can restrict airflow on a furnace that wasn’t designed for it.

  • MERV 8 to 11 in a 1-inch slot: good everyday protection for most Calgary homes.
  • MERV 11 to 13 in a 4- or 5-inch media cabinet: better filtration for pets, allergies and wildfire smoke, without choking airflow.
  • Need more? A HEPA bypass system or other whole-home air purifiers handle the finest particles.

If you want higher filtration, ask a technician to check your furnace’s airflow first.

How to Change a Furnace Filter

  1. Set the thermostat so the furnace isn’t running.
  2. Open the filter slot or cabinet and slide out the old filter. Note which way its arrow points.
  3. Check the size on the frame and match it exactly.
  4. Slide in the new filter with the arrow pointing toward the furnace, in the direction air flows.
  5. Close the cover, turn the furnace back on, and write the date on the filter frame.

Signs Your Filter Is Clogged

  • the filter looks grey, or you can’t see light through it
  • weaker airflow from the vents
  • more dust settling on furniture
  • the furnace turning on and off every few minutes; see our guide to furnace short cycling
  • a whistling sound at the filter slot, or the filter bending inward
  • a dusty burning smell that doesn’t fade

The Filters People Forget

  • Humidifier pad: a furnace humidifier has a water panel that needs replacing about once a year, usually at your fall tune-up. See whole-home humidifiers.
  • HRV filters: many newer Calgary homes have an HRV with washable filters that need cleaning every few months.
  • Ductless and heat pump heads: indoor units have washable filters; rinse them every month or two during heavy use.
  • Range hood filters: grease filters over the stove need regular cleaning too.

Common Mistakes

  • installing the filter backwards
  • using a filter that’s the wrong size, leaving gaps
  • putting a very high-MERV 1-inch filter in a furnace that can’t handle it
  • running the furnace with no filter “just for a few days”
  • forgetting to change it during renovations, when drywall dust clogs filters and coats the blower

Make It Automatic

A yearly furnace tune-up includes checking and replacing the filter, and our Alberta maintenance plans include a free standard filter on Silver and Platinum tiers. For ongoing care through the winter, see furnace maintenance in Calgary, or read our guide to furnace maintenance cost in Calgary.

Frequently Asked Questions

How often should I change my furnace filter in winter?

For a standard 1-inch filter, every 1 to 3 months during a Calgary winter, and monthly if you have pets or allergies. A 4- or 5-inch media filter usually lasts 6 to 12 months. Check it monthly and change it early if you can’t see light through it.

What size furnace filter do I need?

Use the size printed on your current filter’s frame, such as 16x25x1. That’s the nominal size; the actual filter is slightly smaller, which is normal. If there’s no label, measure the old filter or the filter slot and round up to the nearest standard size.

Is a higher MERV filter better?

Not always. Higher MERV ratings catch finer particles, but a dense 1-inch filter can restrict airflow on furnaces not designed for it. For most Calgary homes, MERV 8 to 11 in a 1-inch slot, or MERV 11 to 13 in a 4- or 5-inch media cabinet, works well.

Can a dirty filter make my furnace shut off?

Yes. A clogged filter cuts airflow, so the furnace overheats and a safety switch shuts the burners off. It may then restart and shut off again, which is called short cycling. Replacing the filter often fixes it, but call a technician if it doesn’t.

Which way does a furnace filter go in?

Look for the airflow arrow printed on the filter frame. Point the arrow toward the furnace and away from the return-air duct, in the direction the air travels. A filter installed backwards filters less effectively and can wear out sooner.

Do Purcell maintenance plans include filters?

Yes. Purcell Heating & Air’s Silver and Platinum Alberta maintenance plans include a free standard filter, along with a yearly tune-up and repair discounts. Plans start at $16.99 a month plus GST. See the plan page for the full list of what each tier includes.

Scroll to Top